Envy24control

From the ALSA wiki

Jump to: navigation, search

Envy24control is a graphical utility for controlling cards based on the envy24 or ice1712 chipset, e.g., the Midiman Delta series and the Terratec EWS and EWX series. It is supplied as part of the alsa-tools package. The utility allows control of the digital mixer, channel gains and other hardware settings, as well as displaying a level meter for each input and output channel.

\

http://www.alsa-project.org/alsa/ftp/others/envy24control/envy24_1.jpg

\ The following options are available when invoking envy24control:

The controls may be a little daunting at first, not to mention the potential confusion created with varying number schemes within the same app (DAC0-7 vs CM1-8, etc). DAC analog vol controls are a direct gain control of the analog signal at the analog line pre-amp. Take envy24control in its default state. PCM Out 1/2 are directly routed to H/W Out 1/2. This means that any PCM data that jack sends to alsa_pcm:playback_1/2 (which is PCM Out 1/2 in envy24control) goes directly to H/W Out 1/2, which is the analog rca line outs 1 and 2. Any adjustments you make on the monitor mixer page will have no effect. The analog adjustments DAC0 and DAC1 are your only control.

If you route H/W Out1/2 to Digital Mix L/R, respectively, now you are going to hear whatever audio is on the 'Monitor Mixer'. DAC0 and 1 still need to be up, they are at the analog preamp level so always have to be up no matter what you assign to your H/W Outs. Now that you are monitoring the Digital Mix, you need to 'send' audio to the Mix to be able to hear anything. On the 'Monitor Mixer' tab, what you will hear is what can be seen in the left-most, large Digital Mixer meter. To 'send' audio there, simply unmute and raise the levels for whatever channels you want to monitor.

For example, to duplicate the earlier configuration (PCM1/2 directly routed to H/W1/2), unmute and raise the level completely for the *Left* side only on PCM Out1. Ditto for PCM Out 2, except just the *right* side. Using a typical stereo wav file being played back should show you how audio appears on the Digital Mixer as you made the adjustments. Does it make sense why left on 1 and right on 2? PCM1 is the left channel of a typical stereo audio signal, PCM2 is the right. If you were to up both left and right on PCM1, you are sending the left half of a signal to both sides, creating a mono signal. Do it on both PCM Out 1 and 2, and you have a mono signal at twice the amplitude. I used PCM Out 1/2 here as examples, using a typical stereo wav file as an audio source, but this applies to all the ins/outs, etc.

Now, to monitor some live inputs, head down to any of the HW In channels, and unmute/up level on an In channel that you have an input on (mic, guitar, etc). Make sure to up the level at the analog pre-amp as well, making sure to account for the numbering difference (H/W In 3 is controlled by ADC2, etc). At this point I sometimes run 2 instances of envy24control (yup you can do that) so I can watch the level meter while adjusting the proper ADC. Once that is adjusted, unmute and raise level on the monitor mixer tab and the audio will be sent to the Digital Mixer and you should hear it. That's that...

The IPGA0-7 adjustments on the analog page is an additional gain boost for line inputs. If you turn up an ADC all the way on a given channel, and the signal is still not hot enough, this amplifies it internally, thus adding distortion. In my opinion, anytime you use these you are band-aiding a problem somewhere else.

Retrieved from "http://alsa.opensrc.org/Envy24control"

Category: Alsa-tools

GITHUB | EDIT